Skip to main content

networking - How does my computer's firewall work? Like inbound rule, outbound rule, reply?


So I understand how NAT works, but I don't understand how firewall works. With non-symmetric NAT, if someone sends me a packet, it gets blocked, but it I send someone a packet and they get that packet and then send it back to me, it gets through. I have Windows Firewall on my computer. Does the firewall work the same way (like does it block replies too?)?


My Windows Firewall has some inbound and outbound rules. It also has an option for "all inbound traffic are blocked". When I select "all inbound traffic are blocked" for all networks (public and private), TeamViewer and Skype can still get through (they apparently have inbound rules that were set at installation). Are these inbound rules what allow them to get through? How do the inbound/outbound rules work? If I have "all inbound traffic are blocked" set up and then send someone a packet and they send it back to me, will it still go through? Or does "all inbound traffic are blocked" prevent that?


Please explain software firewall to me. The online resources suck.



Answer



TL;DR, yes, it means that if you make a connection outbound, that the service you connected to can respond. They cannot connect to you unsolicited however, unless you set up port forwarding rules to allow them to.


First, you are confusing Asymetric NAT with Stateful Packet Filtering. NAT does not actually firewall anything, it just allows ports to be translated from source to destination. SPF is whats responsible for allowing only solicited responses to traffic.


TCP is a connection orriented protocol, in that both sides of the transmission negotiate and maintain a virtual connection (a flow of packets that are related, such that the order of packets can be maintained even if they arrive out of order, malformed or missing packets are easily noticed so a resend can be requested, and can perform flow control operations to make sure that traffic does not cause too much congestion).


This connection-orrientation allows the firewall to tell whether a given packet is asking for a new connection, or part of an existing and established one.


SPF is generally set up to allow all outgoing connection attempts, and to allow remote servers to whom a connection has been attempted, to reply in-band within that connection (eg the packet comes from the right source on the right port, has SYN/ACK flags set correctly, and has the correct SYN and ACK values) to come through the NAT.


What SPF generally DOESN'T allow, is a remote server initiating a connection to a service inside the NAT wall. so you can request a remote servers resources, and it can send them to you, but the remote server cannot request your resources.


Port forwarding or Destination NAT allows you to set up a service so that outside servers can initiate connections to it to request resources. you only want to do this if absolutely necessary, as it does open up the service to potential attacks.


Note that with PortForwarding, even once you have a port set up to expose your internal service, you must still allow that port through the firewall, as an incoming connection.


As for what you are seeing with Skype and windows firewall, when it says "block all incomming connections" it means that it will not allow a remote server to create an unsolicited connection to your box. it does NOT mean that it will block replies that are part of a connection initiated from your PC however, so Skype can connect to the skype servers, and those servers can respond as part of that connection.


hope that helps.


Comments

Post a Comment

Popular Posts

How do I transmit a single hexadecimal value serial data in PuTTY using an Alt code?

I am trying to sent a specific hexadecimal value across a serial COM port using PuTTY. Specifically, I want to send the hex codes 9C, B6, FC, and 8B. I have looked up the Alt codes for these and they are 156, 182, 252, and 139 respectively. However, whenever I input the Alt codes, a preceding hex value of C2 is sent before 9C, B6, and 8B so the values that are sent are C2 9C, C2 B6, and C2 8B. The value for FC is changed to C3 FC. Why are these values being placed before the hex value and why is FC being changed altogether? To me, it seems like there is a problem internally converting the Alt code to hex. Is there a way to directly input hex values without using Alt codes in PuTTY? Answer What you're seeing is just ordinary text character set conversion. As far as PuTTY is concerned, you are typing (and reading) text , not raw binary data, therefore it has to convert the text to bytes in whatever configured character set before sending it over the wire. In other words, when y...
Post a Comment
Read more

linux - Extract/save a mail attachment using bash

Using normal bash tools (ie, built-ins or commonly-available command-line tools), is it possible, and how to extract/save attachments on emails? For example, say I have a nightly report which arrives via email but is a zip archive of several log files. I want to save all those zips into a backup directory. How would I accomplish that? Answer If you're aiming for portability, beware that there are several different versions of mail(1) and mailx(1) . There's a POSIX mailx command, but with very few requirements. And none of the implementations I have seem to parse attachments anyway. You might have the mpack package . Its munpack command saves all parts of a MIME message into separate files, then all you have to do is save the interesting parts and clean up the rest. There's also metamail . An equivalent of munpack is metamail -wy .
Post a Comment
Read more

ubuntu - Why does my USB hdd returns SG_IO: bad/missing sense data?

I am able to boot and run commands from external USB hdd; the message in question appears for about 45 seconds then booting continues. GRUB2 is installed on internal HDD. When choosing to boot directly to /dev/sdb the message doesn't appear, however boot time is about the same as booting to internal HDD. /dev/sdb: Timing cached reads: 1018 MB in 2.00 seconds = 508.97 MB/sec Timing buffered disk reads: 80 MB in 3.03 seconds = 26.37 MB/sec pfeiffep@de:~$ sudo hdparm -i /dev/sdb /dev/sdb: SG_IO: bad/missing sense data, sb[]: 70 00 05 00 00 00 00 10 00 00 00 00 20 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 HDIO_GET_IDENTITY failed: Invalid argument Gparted correctly identifies the drive as SAMSUNG MP0402H. Any ideas how to remedy the HDIO & SG_IO messages?
Post a Comment
Read more

Desktop reboots itself on sleep or hibernate

I have been using an ASUS M2NPV-VM motherboard for main home desktop workstation, operating Windows Vista x64. This computer has right from day one not been able to enter hibernate or standby; after Windows performs its final actions and brings the machine down, it would automatically revive itself for a reboot. Updating to the second latest BIOS (1201)has not helped (the latest BIOS revision would induce video refresh problems rendering it unusable). I have been reading related discussions on incidents similar to mine to no avail of a true workable solution. They appear to be more speculative guesses rather than actual knowledge on the inner workings of motherboard hardware. Does anybody have any electronic engineering experience on PC energy-saving standards to provide a more informed opinion how to go about getting this to work? More stories: this motherboard could not even reboot properly the first thing i used it. It was due to refresh rate of the onboard GPU, which had no influe...
Post a Comment
Read more