Skip to main content

memory - Should I be worrying about Single Channel and Double Channel for my RAM?


I've got an Asus P5N-EM HDMI motherboard. When I run CPU-Z, it says my Memory is Single Channel. Currently, i have 2x2GIG Kingston DDR2 ram modules installed.


These are the screenies from CPU-Z:


alt text


alt text


Note: Both slot #1 and slot #3 have the same data.


Should I be trying to go dual channel? Should I care?



Answer



Looking at your board it appears that Slot#1 and Slot#2 (colored black?) should be used for the memory -- this ASUS board has 3 memory slots instead of the usual 4 and they are organized differently. Alternate is not right here.


alt text



A good article discussing Dual-Channel RAM,
Everything You Need to Know About Dual Channel



Dual channel is the ability that some memory controllers have to expand the width of their data busses from 64 to 128 bits. Considering that everything remains the same (clock speeds, for example), the memory maximum theoretical transfer rate is doubled by the use of this technique.


Memories based on DDR (Double Data Rate) technology such as DDR-SDRAM, DDR2-SDRAM and DDR3-SDRAM transfer two data per clock cycle. Because of that they achieve double the transfer rate compared to traditional memories (such as the original SDRAM) running at the same clock rate.


For dual-channel technology to work you need to have an even number of memory modules on your system (assuming that your AMD CPU or Intel chipset support this technology, of course). If you install just one module this technique won’t work because memory will still be accessed 64 bits per cycle. In other words, dual channel works by accessing two memory modules in parallel, i.e. at the same time. Because the two modules are accessed at the same time, they must be identical (same capacity, same timings and same clock rate).



Finally, this is described with more words in the article,
If you have a motherboard with 4 slots, and you own two similar memory sticks compatible with your board, it is critical to place them on the correct two slots (usually alternate slots). The board is wired to use them in dual-channel mode correctly on these placements. Suitable slot pairs are usually colored the same to remind you about this.


So, YES, you should care. You have the right memory (DDR two matched units) and you are running single more just because of incorrect memory placement.


Comments

Post a Comment

Popular Posts

How do I transmit a single hexadecimal value serial data in PuTTY using an Alt code?

I am trying to sent a specific hexadecimal value across a serial COM port using PuTTY. Specifically, I want to send the hex codes 9C, B6, FC, and 8B. I have looked up the Alt codes for these and they are 156, 182, 252, and 139 respectively. However, whenever I input the Alt codes, a preceding hex value of C2 is sent before 9C, B6, and 8B so the values that are sent are C2 9C, C2 B6, and C2 8B. The value for FC is changed to C3 FC. Why are these values being placed before the hex value and why is FC being changed altogether? To me, it seems like there is a problem internally converting the Alt code to hex. Is there a way to directly input hex values without using Alt codes in PuTTY? Answer What you're seeing is just ordinary text character set conversion. As far as PuTTY is concerned, you are typing (and reading) text , not raw binary data, therefore it has to convert the text to bytes in whatever configured character set before sending it over the wire. In other words, when y...
Post a Comment
Read more

linux - Extract/save a mail attachment using bash

Using normal bash tools (ie, built-ins or commonly-available command-line tools), is it possible, and how to extract/save attachments on emails? For example, say I have a nightly report which arrives via email but is a zip archive of several log files. I want to save all those zips into a backup directory. How would I accomplish that? Answer If you're aiming for portability, beware that there are several different versions of mail(1) and mailx(1) . There's a POSIX mailx command, but with very few requirements. And none of the implementations I have seem to parse attachments anyway. You might have the mpack package . Its munpack command saves all parts of a MIME message into separate files, then all you have to do is save the interesting parts and clean up the rest. There's also metamail . An equivalent of munpack is metamail -wy .
Post a Comment
Read more

ubuntu - Why does my USB hdd returns SG_IO: bad/missing sense data?

I am able to boot and run commands from external USB hdd; the message in question appears for about 45 seconds then booting continues. GRUB2 is installed on internal HDD. When choosing to boot directly to /dev/sdb the message doesn't appear, however boot time is about the same as booting to internal HDD. /dev/sdb: Timing cached reads: 1018 MB in 2.00 seconds = 508.97 MB/sec Timing buffered disk reads: 80 MB in 3.03 seconds = 26.37 MB/sec pfeiffep@de:~$ sudo hdparm -i /dev/sdb /dev/sdb: SG_IO: bad/missing sense data, sb[]: 70 00 05 00 00 00 00 10 00 00 00 00 20 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 HDIO_GET_IDENTITY failed: Invalid argument Gparted correctly identifies the drive as SAMSUNG MP0402H. Any ideas how to remedy the HDIO & SG_IO messages?
Post a Comment
Read more

Desktop reboots itself on sleep or hibernate

I have been using an ASUS M2NPV-VM motherboard for main home desktop workstation, operating Windows Vista x64. This computer has right from day one not been able to enter hibernate or standby; after Windows performs its final actions and brings the machine down, it would automatically revive itself for a reboot. Updating to the second latest BIOS (1201)has not helped (the latest BIOS revision would induce video refresh problems rendering it unusable). I have been reading related discussions on incidents similar to mine to no avail of a true workable solution. They appear to be more speculative guesses rather than actual knowledge on the inner workings of motherboard hardware. Does anybody have any electronic engineering experience on PC energy-saving standards to provide a more informed opinion how to go about getting this to work? More stories: this motherboard could not even reboot properly the first thing i used it. It was due to refresh rate of the onboard GPU, which had no influe...
Post a Comment
Read more