Skip to main content

windows - Which network connection is used if connect using multiple interfaces


I'm using Windows 7. I connect to the internet using both my Ethernet port and Wifi.


How can I know which interface is Windows using to connect to the internet? What if there are even more interfaces, like an additional USB Wifi adapters? Is there a general rule for this?



Answer



There are two things you need to look at:



  1. The routing table (and its default interface).

  2. The preferred network settings in windows.


The routing tables are easy. Start a shell and (e.g. start run cmd.exe) and use the command route print. One of the entries will have network destination 0.0.0.0 (that means every destination not explicitly listed). The IP in the column Interface is the IP belonging to the card use to reach the default interface.



IPv4 Route Table
======================================================================
Active Routes:
Network Destination  Netmask     Gateway        Interface      Metric
      0.0.0.0        0.0.0.0    192.168.1.252   192.168.1.12     20

I know this is a bit brief, but there is a nice long answer at in this post on our sister site.


That part is rather generic and works that way for every computer, regardless if it is running windows, CPM, DOS, Linux, BSD, OS X, etc etc.



The second point is windows specific.


Windows defaults to the link with the highest speed.


If you have wireless up to 54Mbit and wire (usually 100mbit or 1000mbit) then windows will use the wired card if it is plugged in, and fall back to the wireless card if it is not plugged it. (This is not always a case of wired over wireless, you can have a 100mbit wired connection and a 300mbit wireless connection).


This might even change when you are waling around with the laptop, or when someone moves between your laptop and the WAP. (Water, and thus human are great absorbers of 2.4 GHz radiation.). Thus the actual used connection can change at any time.


If desired you can manually select which network should be use by going to the local area connection settings under Adapters and bindings.



Edit to answer some of the questions on comments which got to long to answer without using several 'comment posts':



Can you say that the interface with the lowest metric in the route table is the one that is used? – awe



Yes.


If there is more than one path then windows will look first at the most specific path and use that. If there are multiple paths to the same destination then it will use the path with the lowest metric value.


This value may be manually set to indicate cost (as in €/MB), or the number of routers to cross (more a technical cost), or speed.


This post on Serverfault describes how windows sets the default values for the metric.


Other interesting posts are:



  1. Technet: The IP routing table

  2. Technet: The route command

  3. Here on [SU]: How does windows 7 decide which route to take if there are 2 connections



Update for windows 8.1 (with thanks to Joseph Quinsey):


For Windows 8.1, to find the manual selection, you need:



  • Network and Sharing Center

  • Change adapter settings

  • Press Alt

  • Advanced

  • Advanced Settings

  • Adapters and Bindings,


or



  • right-click Start

  • Network Connections

  • Press Alt,

  • Advanced

  • Advanced Settings

  • Adapters and Bindings,


Comments

Post a Comment

Popular Posts

keyboard - Is there any utility/method to change Windows key bindings to type rare chars to currently empty bindings?

I'm currently typing this post with my windows XP machine and (Spanish) keyboard, and I'd like to add some extra symbols to my text. I could open the "char map" windows utility, look for the desired symbols, and paste them. But I'd like something quickier. For example, when I'm using my OSX Mac at work, I can easily add a ©, ™, ® or similar symbols, just pressing some weird ALT-GR + G / H / J, key combinations. In my (Spanish) keyboard mapping, these combinations are empty, as they don't produce any char at all, which, on the other hand, is perfectly normal and desirable. So, I thought: Why couldn't I add some extra key mappings on top of my currently empty ALT-GR + G/J/H Keys in my Spanish keyboard, and thus, being able to quickly type these special symbols? So that's my question: Is there any utility/method to achieve that effect under windows? (My version is XP). I've even googled this for some time but no luck. I've been a long term Hot...
Post a Comment
Read more

virtualization - How to select paravirtualization interface in VirtualBox?

Given a windows 8 host system (Intel Core i5) and a Linux Fedora host, I would like to determine the optimal setting for the paravirtual interface. Options are none Default Legacy minimal Hyper-V KVM This page suggest the selection is only based on the guest system: The biggest change in VirtualBox 5.0 is the introduction of paravirtualization support, bringing higher performance and time-keeping accuracy to supported guest operating systems (Hyper-V on Windows and KVM on Linux). Is that correct? Answer The VirtualBox Manual , in the section titled Paravirtualization providers explains very clearly when each should be used (emphasis added): Minimal: Announces the presence of a virtualized environment. Additionally, reports the TSC and APIC frequency to the guest operating system. This provider is mandatory for running any Mac OS X guests. KVM: Presents a Linux KVM hypervisor interface which is recognized by Linux kernels starting with version 2.6.25. VirtualBox's implementati...
Post a Comment
Read more

Desktop reboots itself on sleep or hibernate

I have been using an ASUS M2NPV-VM motherboard for main home desktop workstation, operating Windows Vista x64. This computer has right from day one not been able to enter hibernate or standby; after Windows performs its final actions and brings the machine down, it would automatically revive itself for a reboot. Updating to the second latest BIOS (1201)has not helped (the latest BIOS revision would induce video refresh problems rendering it unusable). I have been reading related discussions on incidents similar to mine to no avail of a true workable solution. They appear to be more speculative guesses rather than actual knowledge on the inner workings of motherboard hardware. Does anybody have any electronic engineering experience on PC energy-saving standards to provide a more informed opinion how to go about getting this to work? More stories: this motherboard could not even reboot properly the first thing i used it. It was due to refresh rate of the onboard GPU, which had no influe...
Post a Comment
Read more

security - How is Linux not prone to viruses, malware and those kinds of things?

How is Linux protected against viruses? This question was a Super User Question of the Week . Read the blog entry for more details or contribute to the blog yourself Answer Well, it factually is not... it's just less subject to hackers developing viruses that target Linux systems. Consumer grade computers usually run on Windows and thus, when targeting a wide audience, Windows is the way to go. Don't misunderstand Linux and viruses, there definitely ARE Linux viruses. Some distros have additional protection layers such as SELinux (See here ) in Ubuntu for example. Then there's the default firewall and the fact that alien files don't automatically have permission to be executed. Specific execution permission has to be granted before execution is possible. (See here ) Then there are several other factors that make Linux a hard place to be for viruses usually non-root users on linux systems have no to little executable files at their disposal that would allow for virus...
Post a Comment
Read more