Skip to main content

shell - How to correct the unrecognizable code in my debian?


After running programs that output unrecognizable code, the whole shell would be full of unrecognizable code.


alt text


How can I correct this?



Answer



SI/SO VT100 Control Characters


The garbled characters are likely due to the terminal getting a SI character (Shift In; ASCII 14; Control-N). SI is a VT100 control character that can cause the terminal to switch to an alternate character set. Many real terminals (e.g. an actual hardware device, or just the text-only console of an OS) and terminal programs honor this escape code.


The direct way to switch back to the normal character set is to send a SO character (Shift Out; ASCII 15; Control-O) to the terminal.


Recovery


Because the character set is switched, you may have to type the recovery commands “blind” (without relying on seeing what you have typed).


Usually the echo command will be useful. Often you can type
E C H O Space Control-V Control-O Enter / Return
to get the terminal to see a Control-O (the Control-V tells the input-side of the terminal that the next is to be passed literally, otherwise the input side will ‘eat’ the character before it gets the the shell and thus before it can be sent back to the output side of the terminal).


If you can assume a reasonable shell with a printf builtin (or no shell builtin and a reasonable external printf command), you can use printf '\017' to send a Control-O to the terminal.


Comments

Post a Comment

Popular Posts

keyboard - Is there any utility/method to change Windows key bindings to type rare chars to currently empty bindings?

I'm currently typing this post with my windows XP machine and (Spanish) keyboard, and I'd like to add some extra symbols to my text. I could open the "char map" windows utility, look for the desired symbols, and paste them. But I'd like something quickier. For example, when I'm using my OSX Mac at work, I can easily add a ©, ™, ® or similar symbols, just pressing some weird ALT-GR + G / H / J, key combinations. In my (Spanish) keyboard mapping, these combinations are empty, as they don't produce any char at all, which, on the other hand, is perfectly normal and desirable. So, I thought: Why couldn't I add some extra key mappings on top of my currently empty ALT-GR + G/J/H Keys in my Spanish keyboard, and thus, being able to quickly type these special symbols? So that's my question: Is there any utility/method to achieve that effect under windows? (My version is XP). I've even googled this for some time but no luck. I've been a long term Hot...
Post a Comment
Read more

virtualization - How to select paravirtualization interface in VirtualBox?

Given a windows 8 host system (Intel Core i5) and a Linux Fedora host, I would like to determine the optimal setting for the paravirtual interface. Options are none Default Legacy minimal Hyper-V KVM This page suggest the selection is only based on the guest system: The biggest change in VirtualBox 5.0 is the introduction of paravirtualization support, bringing higher performance and time-keeping accuracy to supported guest operating systems (Hyper-V on Windows and KVM on Linux). Is that correct? Answer The VirtualBox Manual , in the section titled Paravirtualization providers explains very clearly when each should be used (emphasis added): Minimal: Announces the presence of a virtualized environment. Additionally, reports the TSC and APIC frequency to the guest operating system. This provider is mandatory for running any Mac OS X guests. KVM: Presents a Linux KVM hypervisor interface which is recognized by Linux kernels starting with version 2.6.25. VirtualBox's implementati...
Post a Comment
Read more

How do I transmit a single hexadecimal value serial data in PuTTY using an Alt code?

I am trying to sent a specific hexadecimal value across a serial COM port using PuTTY. Specifically, I want to send the hex codes 9C, B6, FC, and 8B. I have looked up the Alt codes for these and they are 156, 182, 252, and 139 respectively. However, whenever I input the Alt codes, a preceding hex value of C2 is sent before 9C, B6, and 8B so the values that are sent are C2 9C, C2 B6, and C2 8B. The value for FC is changed to C3 FC. Why are these values being placed before the hex value and why is FC being changed altogether? To me, it seems like there is a problem internally converting the Alt code to hex. Is there a way to directly input hex values without using Alt codes in PuTTY? Answer What you're seeing is just ordinary text character set conversion. As far as PuTTY is concerned, you are typing (and reading) text , not raw binary data, therefore it has to convert the text to bytes in whatever configured character set before sending it over the wire. In other words, when y...
Post a Comment
Read more

Desktop reboots itself on sleep or hibernate

I have been using an ASUS M2NPV-VM motherboard for main home desktop workstation, operating Windows Vista x64. This computer has right from day one not been able to enter hibernate or standby; after Windows performs its final actions and brings the machine down, it would automatically revive itself for a reboot. Updating to the second latest BIOS (1201)has not helped (the latest BIOS revision would induce video refresh problems rendering it unusable). I have been reading related discussions on incidents similar to mine to no avail of a true workable solution. They appear to be more speculative guesses rather than actual knowledge on the inner workings of motherboard hardware. Does anybody have any electronic engineering experience on PC energy-saving standards to provide a more informed opinion how to go about getting this to work? More stories: this motherboard could not even reboot properly the first thing i used it. It was due to refresh rate of the onboard GPU, which had no influe...
Post a Comment
Read more